Cat C15 6nz Injector Torque Specs. End By: Install the valve mechanism cover. EPA Tier 3 equivale
End By: Install the valve mechanism cover. EPA Tier 3 equivalent, and EU Stage IIIA Doing an in-frame overhaul on a C-15 in an '04 Pete 378. Many parts are interchangeable It details the required tools, the adjustment procedure for injectors on specific cylinders, and the necessary measurements and torque specifications. My rocker shaft/jake bolts have Cat c15 6nz need valve injector also jake brake adjustment values and torque spec for rocker lever shaft Mechanic's Assistant chat Customer: I need the valve injector specifications for a C15 6NZ engine, I need overhaul torque specs for the c-15 acert. The additional turn provides the d The Cat® C15 Industrial Diesel Engine is offered in ratings ranging from 354-433 bkW (475-580 bhp) @ 1800-2100 rpm. Hidden engine problems and reliability issues most Torque Specifications for All Caterpillar Products Low Cost Maintenance Worldwide service delivers ease of maintenance and simplifies the servicing routine. It includes tables listing the recommended torque values for C15 and C18 – Engine Valve Lash – Inspect/Adjust Note: Valve lash is measured between the rocker arm and the valve bridge. Repeat Steps 1 and 2 for the remainder of the rocker arm assemblies. Note: Install rocker shaft (3) with the flat side facing upward. between startability and desired road speed. S. Looking for proper torque specs for torquing the jake assemblies, as well as torque for Install rocker shaft (3), valve rocker arms (1), and unit injector rocker arms (4) as a unit with Tooling (A) . Illustration 3 g00517442 Note: If the Discover the power and performance of the Cat 6NZ engine with detailed specs, configuration, and maintenance information. Rocker shaft bolts must be tightened evenly to For the 2003 Cat C-15 engine, use a calibrated torque wrench to tighten injector hold-down bolts to manufacturer specs, typically around 30-40 ft-lbs. EPA Tier 4 Final, EU Stage V, Japan 2014, and Korea Tier Hold the adjustment screw in this position and tighten locknut (3) to a torque of 100 ± 10 N·m (74 ± 7 lb ft). The C15 On-Highway Diesel Engine offers a wide operating range and high torque rise, which promotes the use of transmissions with fewer gears. It includes specific torque values for the Engine Model: C15, 14. Turn the flywheel by 360 degrees in the direction of engine rotation. The Cat® C15 Industrial Diesel Engine is offered in ratings ranging from 328-444 bkW (440-595 bhp) @ 1800-2100 rpm. lb. Posts: 154 Threads: 37 Joined: Apr 2011 2 11-19-2013, 11:18 PM Head bolt torque; 315 + - 15 ft. It details the required tools, the adjustment procedure for injectors on For the Cat C15 engine, proper torque on injector hold down bolts ensures injector stability and prevents leaks. It was an MBN, now its a 6NZ with a platinum O/H kit. There is an initial torque a d an additional turn. It also seems to have a slight miss or Injector Lash Settings Testing and Adjusting C-15, C-16 and C-18 Engines Media Number -RENR2307-03 For the C15 6NZ engine, rod bolts typically torque to about 90-100 ft-lbs plus an angle specification, while main bearing caps require around 150-160 ft-lbs. I am a heavy duty tech very familiar with previous cats ie 3406 B, E, c-12, c-15, etc and have I'm looking for a document showing the power and torque curves or power/torque per RPM specifications of the CAT3406E (2WS) or the C15 (6NZ) engines (factory tuned). The document provides torque specifications and calibration steps for various components of the CAT C15 engine. These ratings meet U. The document is part of the technical Does anyone have access to find out the torque values for all the components of a c15 mbn25915. Always use a calibrated torque wrench and The early C15s with a 6NZ serial number prefix only have one turbocharger and simple electronics, and weigh less than the 3406E, which was the C15s predecessor. injector bolts :45 ft lbs intake valve . Save time and money by performing this C-15 and C-16 Industrial Engines – Electronic Unit Injector – Adjust To make an adjustment to the unit injectors on cylinders 3, 5, and 6 use the I have combustion gas getting into the return fuel on my 550 6NZ. Refer to This document provides instructions for adjusting the electronic unit injectors on Caterpillar C-15 Truck Engines (6NZ00001-UP). 020 The Cat<sup>®</sup> C15 Industrial Diesel Engine is offered in ratings ranging from 354-433 bkW (475-580 bhp) @ 1800-2100 rpm. The initial torque is required to bring all parts of t e joint into contact. It's apparent because I have smoke in my fuel tanks when I remove the fuel caps. Even with this built-in feature, heavy/ specialty haulers . 028 iva . 015 exhaust valve . In general, either application shares one similar Install four bolts (2). If applicable, minimum 5000 -hour diesel particulate filter (DPF) ash service interval enables The document provides torque specifications for fasteners used on Caterpillar and Mitsubishi engines. Tighten bolts (2) to a torque of 109 ± 15 N·m (80 ± 11 lb ft). Typical loads of 80 000 Ib or less are less affected by improp r drive train specing than are heavy haulers. To make an adjustment to the unit injectors on cylinders 1, 2, and 4, remove the timing bolt. Engine is disassembled, waiting for parts, and ready to start inframe. I put in a 6NZ cam, rocker shafts and rockers also. 6L Engine Notes: supply engine serial number and arrangement number Other Notes: Year/Serial: Fuel: Diesel Cylinders: 6 Bore: Torque-Turn ng force is required. All measurements Head Bolt, Connecting Rod Bolt & Main Bearing Bolt Torque Specifications Caterpillar® 3406A • 3406B • 3406C • 3406E • C15 Cummins® ISX • ISM11 • N14 Detroit Diesel® Series 60 You can do injector height with a digital calliper set too spec To make an adjustment to the unit injectors on cylinders 3, 5, and 6 use the following procedure: To make an adjustment to the unit injectors on cylinders 1, 2, and 4, remove the timing bolt. These ratings meet China Stage II, U. 030 exhaust brake . Industries and applications Learn how to change injectors on your C15 Cat engine with our comprehensive step-by-step guide. Rocker arm bolts usually require 25-35 ft-lbs, while I am just getting my C15 overhaul finished up.